How To Install Rear View Camera 2006 Honda Accord

A solid, high-quality backup photographic camera is an essential investment to raise your confidence and safety while reversing a vehicle. This is particularly important in big vehicles or trucks with trailers or equipment, which can exist difficult to maneuver and create blind spots. A backup photographic camera is a simple solution that is like shooting fish in a barrel to install yourself to eliminate blind spots and assistance you maneuver with ease and confidence, instead of straining your neck and risking dents and dings. Simply non every backup camera installation is a straightforward i, such every bit instances where the tailgate of a truck is removed to conform equipment and hauling needs.

This was the instance of ane man driving a 2019 Ford F-250 equipped with a tailgate common salt spreader. The salt spreader is large plenty to block the driver's rear view, while also extending from the back of the truck. This made it challenging to safely back the truck out of driveways, in parking lots, and down streets. A backup photographic camera was the obvious solution, but nigh backup cameras are installed on a truck's tailgate. The tailgate was removed from the bed to suit the spreader, leaving few options for locations to install the fill-in camera.

Then, how do y'all install a backup camera on a truck without a tailgate? Thanks to Camera Source, backup cameras are not only easy to install yourself, they are easy to customize to accommodate your unique needs. Continue reading to find out how to install an OEM backup camera on Ford SuperDuty with the tailgate removed, and watch the video posted by DS Trucks

Getting Started

Every Camera Source fill-in camera installation kit comes with like shooting fish in a barrel step by step instructions for DIY installation. Since the truck owner in the video doesn't have a tailgate to install the fill-in camera on, they got artistic and installed the camera directly on the table salt spreader. We'll summarize how they did it and compare and contrast what they did with the typical installation process, along with tips on other means to customize and improvise.

Required Tools

Phillips head screwdriver
Tape measure
Drill
14mm or nine/16" drill bit
File for deburring
Rubbing alcohol

Included in the kit

Photographic camera bezel
Camera (CS-FTRSK-17SDRC)
Wire Harness
four housing screws
2 self tapping installation screws

Stride 1. Identify the Center of the Vehicle

Y'all want to install the camera at the eye of the vehicle for the best viewing angle. On a Ford SuperDuty, that's unremarkably around 48 inches high. You will run across in the video that they determined the center acme past recognizing where the fill-in camera was positioned on the tailgate earlier it was removed. For their purposes with the salt spreader, they preferred the viewing angle when the camera was positioned at a height of 58 inches.

Modifying the height of the photographic camera makes a large departure because it can give you a smaller or wider field of vision. Y'all will notice in the video, the installer wasn't able to see the end of the salt spreader, merely they had a longer range of view of the area behind them. At this height, they were comfy with the level of visibility of the area behind the truck and of the salt spreader to monitor it.

Stride 2. Clean the Surface & Adhere the Camera

Clean the surface where you lot're going to be installing and mounting the camera and then the adhesive will stick while securing information technology with screws. Call up you're going to need to drill nine/sixteen" holes in the surface you're attaching the backup photographic camera to.

One of the nice features of Camera Source backup cameras is that the enclosures include agglutinative strips to aid determine the ideal placement and hold the camera in place until it is secured with screws. Since this truck was already equipped with a backup camera and monitor, they were easily able to connect the camera and bank check the field of vision for adjustments earlier attaching it with screws.

Step 3. Wiring & Attaching the Camera

Normally when yous install a backup camera, yous drill into the surface of the vehicle to run the wiring through the interior to the power source under the spare tire or under the bumper. In the video, since they tin't run the wire through the salt spreader, they fabricated a slight amending to the camera housing to accommodate for this. They drilled a small hole on the side to allow the wire to get out the housing and along the outside.

So they secured the wiring with tape along the outside and arranged the backlog wiring with a prophylactic ring to forestall it from hanging down and snagging. From there, the wire could exist run through the holes for the previous camera and plugged in.

In one case the camera is positioned where you like it, screw the camera in place inside the enclosure, and screw the enclosure to the surface.

Fill-in Camera Solutions

You may notice in the video, that some backup camera systems are designed to allow for multiple cameras for multiple viewing angles. This is especially helpful in situations where a commuter needs to be able to see behind the equipment they are operating, as well equally the equipment itself to make sure it'south properly operating. Multiple cameras are also helpful for hitching trailers to trucks and backing trailers up with ease. Whatever the example, maximizing your range of vision is e'er smashing for rubber and convenience. Browse our pick of backup cameras. If you lot're looking for unique backup camera installation solutions, scan our expansive selection of cameras , start exploring our resource , or contact u.s. for a custom order if you lot can't find what you lot're looking for.

Source: https://camerasource.com/blog/superduty-oem-rear-camera-installation-rear-camera-solution-when-tailgate-is-removed/

Posted by: jacksonpeand1935.blogspot.com